Author Topic: Tech Tip: PC III Issues  (Read 5096 times)

Offline TALLMAN

  • Tarmac Tearer
  • ***
  • Location: South France
  • Posts: 104
  • Country: fr
  • Total likes: 41
  • Gender: Male
  • THINKING ABOUT IT
PC III Issues
« on: Friday, 23 March 2018, 06:25 pm »
My PC III seems not tobe communicating with the bike,very difficult to start & once started very difficult to keep running, I checked the minus connection to the battery  - good connection, I checked that the mapping was still loaded & reloaded it to be sure, the bike starts and runs fine if I disconnect the PC III, all plugs are clean and not corroded, anybody any ideas ?
« Last Edit: Friday, 23 March 2018, 09:54 pm by gsxbarmy »
HONI SOIT QUE MAL Y PENSE       UBIQUE!       QUO FAS ET GLORIA DU****        FACIMUS ET FRANGIMUS

Offline seth

  • Forum Donor 2020
  • Needs to get out more
  • ******
  • Location: Near Perth in southern Scotland
  • Posts: 5476
  • Country: scotland
  • Total likes: 3435
  • Gender: Male
  • Near to Perth in Scotland
Re: PC III Issues
« Reply #1 on: Friday, 23 March 2018, 07:00 pm »
It could be a pc111 fault they do go wrong sometimes.
Only things I could suggest it contact dynajet and ask them the same question .
The other is if anyone has a pc111 you can swop over with your map to check things that way.
Sorry I'm not much help
 :cheers:
« Last Edit: Friday, 23 March 2018, 09:54 pm by gsxbarmy »
only a slightly modified gsx1400
oh and a standard one too

Sethbot Postwhore

Offline gsxbarmy

  • Forum Legend
  • Administrator
  • *****
  • Location: Essex, UK
  • Posts: 4783
  • Country: england
  • Total likes: 3708
  • Gender: Male
Re: PC III Issues
« Reply #2 on: Friday, 23 March 2018, 08:16 pm »
It may be Richard that the firmware needs re-installing / updating. I seem to recall what you are experiencing being experienced by Duckula many years ago and updating the firmware sorted it. Just make sure your Dyno map is secure before starting the update Richard!!!!!

Downloads are on the Powercommander site here for PCIII:

http://www.powercommander.com/powercommander/downloads/powercommander_downloads.aspx?ProdType=PCIIIUSB
« Last Edit: Friday, 23 March 2018, 09:54 pm by gsxbarmy »
Nothing to do.............all day to do it....I love retirement :lol:

Offline TALLMAN

  • Tarmac Tearer
  • ***
  • Location: South France
  • Posts: 104
  • Country: fr
  • Total likes: 41
  • Gender: Male
  • THINKING ABOUT IT
Re: PC III Issues
« Reply #3 on: Saturday, 24 March 2018, 05:51 pm »
Well I've emailed Dynojet UK , lets see what they say.
HONI SOIT QUE MAL Y PENSE       UBIQUE!       QUO FAS ET GLORIA DU****        FACIMUS ET FRANGIMUS

Offline TALLMAN

  • Tarmac Tearer
  • ***
  • Location: South France
  • Posts: 104
  • Country: fr
  • Total likes: 41
  • Gender: Male
  • THINKING ABOUT IT
Re: PC III Issues
« Reply #4 on: Saturday, 31 March 2018, 04:51 pm »
Dynojet Uk says I have to go ,through the French importer  :rolleyes: I have a spare ECU which I put on the bike this weekend, reconnected the PCIII, reprogrammed it & did 350kms yesterday sweet as !!!!!
HONI SOIT QUE MAL Y PENSE       UBIQUE!       QUO FAS ET GLORIA DU****        FACIMUS ET FRANGIMUS

Offline RickC

Re: PC III Issues
« Reply #5 on: Sunday, 01 April 2018, 01:54 pm »
I had an early model serial PC3 that would play up a bit, I found that the sockets on the plugs had loosened up a bit and were giving
intermittent faults, removing the O Rings on the plugs let the contact make a bit better and all faults disappeared for the 6 months after that I had it for.

Offline diebythereaper

Re: PC III Issues
« Reply #6 on: Thursday, 23 May 2019, 06:50 am »
.
« Last Edit: Sunday, 26 May 2019, 08:25 pm by diebythereaper »

Offline diebythereaper

Re: PC III Issues
« Reply #7 on: Thursday, 23 May 2019, 06:51 am »
For this type of Power Commander 111

 

SMF spam blocked by CleanTalk